2 Wire Fire Alarms

The AlarmSense Open-Area Sounder VID is designed for use in open-areas. Features: Synchronised flashing red LED on sounder visual indicators and v...

The Fike 25-0015-301 Multipoint head removal tool is used to release the optical chamber on older Rafiki/Fike Multipoint detector/sounder and also ...

Twinflex Hatari sounders - for higher sound output requirements. The twinflex Hatari is designed to comply with the European standard EN54 part 3. ...

The Manual Call Point has been designed to operate on an AlarmSense two-wire loop. An alarm is initiated by pressing the resettable element, which ...

The Manual Call Point is used to manually initiate an alarm signal on the fire detection system. Features: EN 54-11 Certified 'Plug and Play' term...

The base is designed to be used with AlarmSense systems only. It is supplied with a low or high volume setting and red or white caps are available ...

The base can only be used with AlarmSense systems. It is fitted with electronic circuitry to monitor the presence of detectors and signals any unau...

An AlarmSense detectors can only be mounted into the AlarmSense Base. The base is used for installing detectors that do not require an integral sou...

The AlarmSense Heat Detector (A1R) has a fixed upper limit, but in addition, measures the rate of increase in temperature. Features: Can be used f...

The AlarmSense Optical Smoke Detector works using the light scatter principle. The detector changes to alarm state at a pre-set threshold of smoke ...

The 45-0022 comes in a pack of 5 and is suitable for the Fike Twinflex Callpoints.

The 25-0083-303 is a cover flap that can be fitted to Fike's manual call point range in order to reduce the risk of accidental operation. Features ...

The Twinflex Manual Call Point allows for user activation of the fire alarm system. Once operated the device latches into the alarm position and re...

Using the ASD Multipoint detector with sounder and/or strobe as part of the TWINFLEXpro 2-wire fire alarm system means that when a detector is wire...

Using the ASD Multipoint detector with sounder and/or strobe as part of the TWINFLEXpro 2-wire fire alarm system means that when a detector is wire...

The Multipoint and ASD detectors have set new standards in detector technology. The TWINFLEX Multipoint head is a 2-wire device used with the TWINF...

LPCB certified to EN54-2/4, C-TEC’s CFP two-wire 8 zone AlarmSense fire panel is designed to work with Apollo’s AlarmSense range of detectors, call...

LPCB certified to EN54-2/4, C-TEC’s CFP two-wire 4 zone AlarmSense fire panel is designed to work with Apollo’s AlarmSense range of detectors, call...

LPCB certified to EN54-2/4, C-TEC’s CFP two-wire 2 zone AlarmSense fire panel is designed to work with Apollo’s AlarmSense range of detectors, call...

The TWINFLEXpro2 repeater panel is smaller than the TWINFLEXpro2 control panel.  It does not connect to or control detection devices. Instead, it c...

The TwinflexPro2 panel is an intelligent 2-wire panel that utilises a conventional type cabling format. The system is classed as Analogue non-addre...

The TwinflexPro2 panel is an intelligent 2-wire panel that utilises a conventional type cabling format. The system is classed as Analogue non-addre...

The TwinflexPro2 panel is an intelligent 2-wire panel that utilises a conventional type cabling format. The system is classed as Analogue non-addre...

The Fike 604-0008 is a 8 Zone Contractor Kit ideal for use in buildings in the UK. A conventional 2-wire fire alarm system is often the natural cho...

The Fike 604-0004 is a 4 Zone Contractor Kit ideal for use in buildings in the UK. A conventional 2-wire fire alarm system is often the natural cho...

The Fike 604 0002 is a 2 Zone Contractor Kit ideal for use in buildings in the UK. This kit is based upon the popular Fike Twinflex Pro range of tw...